Easter Bunny Candy Jar Gnome

In today’s post: Turn a mason jar into an Easter bunny gnome in just a few simple steps, then fill it with candy to make an adorable gift. No sewing required!

Easy DIY Easter Craft

These little Easter bunny candy jar gnomes work can be used as a decoration or given away as a fun gift! You can make one in about twenty minutes using hot glue – no sewing! I’m including a printable pattern that will make cutting out the hat, beard, and ears super simple. This pattern will fit standard size mason jar lids (not wide mouth lids) on either pint or quart jars.

Supplies

Here’s what you’ll need to make a candy jar gnome:

• Sheets of 9×12 craft felt in desired colors: I used pink for the hat, white for the ears, and a cream color for the inside of the ears. I prefer using the “premium” sheets of felt that are a little bit thicker, but normal craft felt works too. In the photo above the pink is a “premium” felt and the aqua is standard. I purchased these at Hobby Lobby for $.25 and $.39 each.
• Faux Fur: You need just a small piece of faux fur for each gnome, only about 3 inches square. I purchased a piece of fur from Hobby Lobby in the craft section near the felt for $2.99. You can also buy a narrow strip of fur off the bolt at a fabric store or order sheets of fur from Amazon.
• 1 inch Wood Dowel Caps or Wood Ball Knobs: I purchased wood dowel caps at Hobby Lobby. You should be able to find them (or the ball knobs) at any craft store. Just be sure not to get wood beads, which have a hole running all the way through them.
• Mason Jar and Lid: You want a mason jar with a standard size lid, not a wide mouth lid. I think these look cutest with pint size jars, but they will work with quart size jars too.
• Pattern: Get the pattern from the blue box directly above the heading “supplies”.

How to Make an Easter Bunny Candy Jar Gnome

This easy Easter craft will take about twenty minutes to make. You will need a hot glue gun. Once you’ve gathered your supplies and printed the pattern, here’s what you’ll do:

Cut Out the Pieces

Begin by cutting each pattern piece out, then use the pattern to cut the felt and fur. For the hat, fold a sheet of craft felt in half and line up the side that says “fold” on the pattern with the fold on the felt, then cut out the hat. Cut the larger ear pieces from white felt. Cut the inner ear pieces from cream felt. Then trace the beard pattern on the back of faux fur and cut it out.

NOTE: When cutting fur, you DO NOT want to just use scissors and cut it out like you would any other fabric because then the fur along the edges of the beard will be very short. To make sure you get the long “beard” effect on the fur, you have two options. First, you can use a razor blade or exacto knife and cut from the back of the fur, cutting through the backing only. Second, you can use sharp scissors, but you’ll want to cut with the back of the fur facing you, and slide the bottom of your scissor through the fur very close to the backing. Your goal is to just cut the backing, not any of the fur itself.

This is what the pieces will look like once cut:

Glue the ears together

Place the inner ear pieces on top of the larger ear pieces. You should have two ears that are mirror images of each other and point slightly outward. Use a small line of hot glue on the bottom and a dot of hot glue at the top to glue the inner ears onto the larger ear pieces. Then place the ears on the hat about an inch up from the bottom, as shown below. Use a line of hot glue *only across the bottom of the ears* to secure them to the hat.

Add Ears and Beard

Fold the bottom edge of the hat up one inch and use hot glue to secure. When using hot glue on felt, you’ll need to work a few inches at a time and hold the felt in place for 15-20 seconds until it’s secure.

Next, run a line of hot glue along the very top edge of the beard. Center the beard below the hat.

Slide the beard up under the hat and press down to secure.

Glue the hat Together

Next, flip the hat over. Fold one side of the hat down so the diagonal edge is straight up and down. Place hot glue along the edge for the top couple of inches. Fold the other side of the hat over so it overlaps by about a quarter of an inch.

Continue adding hot glue, a few inches at a time, to glue the sides of the hat together. Here’s what it will look like from the back when finished:

Glue on the Nose

The last step is to glue on the wood dowel cap or ball knob for a nose. At the top center of the beard, pull the fur apart so you can see the backing. Add hot glue to the back of the wood ball and press it down, holding for a few seconds until secure.

Now the Easter bunny gnome hat for your candy jar is complete! You have a couple options at this point: you can fill the jar with candy, screw on the lid, and just place the hat on top of it. Or if you’d like, you can glue the hat to the lid – just run a line of hot glue around the outside of the lid before placing the hat on it.